Titan Controls® CO2 Inline Heater

Part #{{activeImage.ParentId}}
Titan Controls® CO2 Inline Heater
Part #{{activeImage.ParentId}} Download Image
Titan Controls® CO2 Inline Heater
The Titan Controls® CO2 heater was designed to prevent CO2 regulator freeze-up and avoid cracking the internal diaphragm of the regulator due to high flow conditions. The CO2 Heater is installed between the CO2 cylinder valve and the regulator and warms the gas stream allowing for increased flow rates without regulator freeze-up. The CO2 Heater may be used in conjunction with a Titan Controls® CO2 Greenhouse Regulator or any other CO2 regulator system. Manufactured in USA with aluminum case and solid brass expansion chamber. Solid brass fittings for CO2 cylinders, CGA 320. Completely enclosed heating element. Not for use on GFI protected circuits. 1 Amp/120 Volts/60 Hz.

  • Aluminum case and solid brass expansion chamber
  • Warms CO2 gas to approximately 174°F
  • Completely enclosed heating element
  • Solid brass fittings for C02 cylinders, CGA 320
  • Capacity = 90 scfh maximum
  • Maximum PSI = 1000 PSI
  • Comes with two (2) plastic tank washers
  • NEMA 5-15 grounded power cord
  • 1 Amp/120 Volt/60 Hz
  • 1 year warranty
702715 - Titan Controls CO2 Inline Heater
Download Application Diagram (PDF Document)
Download Instructions (PDF Document)
702715 - Titan Controls CO2 Inline Heater
  EACH CASE PALLET
Upc: 870883009670
Quantity:
Volume (cf): 0.087
Dim Weight (in3/lb): 0.7735
Weight (lb): 1.85
Length (in): 6.1
Width (in): 6
Height (in): 4.1
702712 - Titan Controls CO2 Regulator Replacement Plastic Washer
  EACH CASE PALLET
Upc: 847127007952
Quantity: 1000
Volume (cf): 0.000 0.5694
Dim Weight (in3/lb): 0.0001
Weight (lb): 0.01 5.51
Length (in): 0.75 14.37
Width (in): 0.75 10.24
Height (in): 0.02 6.69
I want to use a GFI (Ground Fault Interrupt) circuit to run my CO2 Heater. Is this possible?
No, you cannot use the CO2 Heater on a GFI circuit. The CO2 Heater grounds out using the metal chassis and will trip your GFI circuit because of this fact. It is recommended to plug the CO2 Heater directly into a standard 15 Amp/120 Volt household circuit.
Can I use an in-line CO2 Heater on a liquid propane tank?
No, due to the temperature difference between the liquid propane and the CO2 Heater can potentially be explosive. This is NOT recommended by the Manufacturer.
What is the maximum PSI (Pound force per Square Inch) that the CO2 Heater will handle?
The maximum PSI that the CO2 Heater is rated for is 1000 PSI (68.9 BAR). The CO2 Heater is intended for indoor use only and is NOT waterproof. Do not handle if it is wet. The temperature on the metal cylinder may exceed 175° F, so be cautious and do not touch the CO2 Heater when operating.

    Sort By:
   Brand:
    Category:
Sorry No Results Found...
Title MSRP Wish List
{{part.PartId}}
{{part.PartId}}
{{part.Name}}
{{part.Name}}
{{part.Message}}
NEW
{{Sunlight.Web.Utility.GetFormattedPrice(part.EachMsrp)}}
 Wish List
 Find Retailer
Your results were limited to 50 items. You may want to be more specific.